The Plunge Lab

Calculators

Cold Plunge Chiller Size Calculator (BTU)

Enter your tub's gallons and set point: get the BTU/hr to buy, the store label that clears it, the pulldown time and the ice it replaces.

gal

Use the fill volume from the tub listing, not the shell's total.

°F
°F
Round up a size if any apply

Cooling capacity to buy

1,500BTU/hr

100 gal × 15-20 BTU/hr per gallon = 1,500-2,000 BTU/hr. Nothing on your list calls for margin, so the bottom of the range is enough.

Store label that clears it

1/2 HP

The 1/2 HP class prints 4,100-5,750 BTU/hr on the published spec tables. The floor of that range is what we compare against your target, because labels are rated on warm water and deliver less as it gets colder. A 1/4 HP unit clears the number on paper, but its makers rate it for 80-92 gallons at most, and your tub holds 100.

Heat to remove on the first pulldown

16,680BTU

100 gal × 8.34 lb = 834 lb of water; × 20°F (65 to 45) = 16,680 BTU. Ideal-conditions time: 1/4 HP about 7.6 hr, 1/2 HP about 4.1 hr, 1 HP about 1.7 hr. Real pulldowns run longer because heat leaks back in the whole time.

The same job with bagged ice

116lb of ice

Melting a pound of ice absorbs about 144 BTU, so 16,680 ÷ 144 = 116 lb, about 6 twenty-pound bags, every time the water warms back up.

How the chiller size is worked out

Two numbers decide it. The first is a sizing rule: 15-20 BTU/hr of cooling per gallon of water. The second is the pulldown: a gallon of water weighs 8.34 lb, and one BTU moves one pound of water one degree Fahrenheit, so pounds times degrees is the heat a chiller has to remove before you can plunge.

The rule carries margin on purpose. The Active Aqua manual and the Penguin and EcoPlus spec tables print a BTU/hr figure without the water temperature it was measured at, capacity falls as the water gets colder, and heat leaks back in through the walls and the water surface. The full reasoning is in what size chiller a cold plunge needs.

Why the calculator compares the floor of each class

The 1/2 HP label covers 4,100-5,750 BTU/hr across brands, so a class is only as good as its weakest published unit. The calculator picks the smallest class whose lowest rating still clears your target. If you are choosing between 1/2 HP and 1 HP, the 1/2 HP vs 1 HP guide works the trade in full.

Running cost is a separate question with its own inputs; the running cost calculator takes a published wattage and your rate.

Frequently asked

How many BTU do I need to cool a cold plunge?
Gallons times 15-20 BTU/hr. A 100 gallon tub wants 1,500-2,000 BTU/hr. Take the top of the range for a hot space, two users back to back, a set point under 42°F, or an uncovered outdoor tub.
How long does a chiller take to cool a tub?
Pounds of water times the degrees you drop, divided by the chiller's BTU/hr. 100 gallons is 834 lb; cooling it 20°F removes 16,680 BTU, about 4 hours for a 4,100 BTU/hr 1/2 HP unit in ideal conditions. Real pulldowns run longer because heat leaks back in the whole time.
Is a 1/4 HP chiller enough for a cold plunge?
On paper, for a small tub: the 1/4 HP class prints 2,200-2,300 BTU/hr, which clears the 1,500-2,000 target for 100 gallons. Labels are rated on warm water, though, so the 1/2 HP class (4,100-5,750) is the standard pick for anything above about 80 gallons or in a warm space.